U.S. flag An official website of the United States government
  1. Home
  2. Medical Devices
  3. Medical Device Safety
  4. Letters to Health Care Providers
  5. Potential Risk of Aluminum Leaching with Use of Certain Fluid Warmer Devices - Letter to Health Care Providers
  1. Letters to Health Care Providers

Potential Risk of Aluminum Leaching with Use of Certain Fluid Warmer Devices - Letter to Health Care Providers

September 15, 2021

The U.S. Food and Drug Administration (FDA) is reminding health care providers about the use of certain fluid warmers and the potential for aluminum leaching and exposing the patient to high levels of aluminum. Based on information reviewed by the FDA, aluminum leaching may occur when the fluid warmer is designed with an aluminum heating element where the heated aluminum is in direct contact with the fluids or blood products being administered to a patient.

The FDA has identified the devices listed in the table below as having this type of design. Three original equipment manufacturers (Eight Medical International BV, Smisson Cartledge Biomedical and Smith Medical) provided revised instructions for use for these devices, a type of voluntarily recall action, which were initiated on the dates shown.  Users who did not purchase devices from these original equipment manufacturers may not be aware of the revised instructions.  A fourth original equipment manufacturer (Vyaire Medical) voluntarily removed its product from the market.

Manufacturer Name Device Information Recall Notice
Eight Medical International BV

Recirculator 8.0 Disposable Lavage kit (Product Code: 8100)

Lot Numbers: 20021361, 20202106, 20018480, 19854186, 20019438, 19854185, 20019438, 19854184, 18687686

Recall Notice
Initiated June 4, 2021
Smisson-Cartledge Biomedical

ThermaCor 1200 Disposable Sets

Disposable Set Models: PTC-1200, DNC-1200, PNC-1200

Recall Notice
Initiated February 18, 2021
Smiths Medical

Level 1 Fluid Warmer
Models: H-1000, H-500

Level 1 Fluid Warming System
Models:  H-1028, H-1200

Level 1 Normothermic I.V. Fluid Administration Set
Models: D-100, D-300, D-50, D-60HL, DI-100, DI-300, DI-50, DI-60HL

NORMOFLO Irrigation Warming Set 
Models: IR-40, IR-500, IR-600, IR-700, IRI-600, IRI-600B, IR-700

Recall Notice
Initiated August 6, 2021

Vyaire Medical enFlow Fluid Warmer System Disposable Cartridges
Models: 980200EU enFlow - Disposable Cartridge, 980202EU enFlow - Disposable Cartridge with IV Extension Set
Recall Notice
Initiated March 13, 2019


The FDA recommends health care providers:

  • Be aware that aluminum leaching from some fluid warmers may occur when both of the following conditions are present:
    • The fluid warmer is designed with an aluminum heating element.
    • The aluminum heating element is in direct contact with the fluids or blood products being administered.
  • Be aware that higher levels of aluminum leaching may generally occur under the following conditions:
    • Lower flow rates
    • Higher warming temperatures
    • Certain fluids, including balanced electrolyte solutions, may leach more aluminum than other solutions (such as Lactated Ringers solutions) 
    • Longer duration of use.
  • Be aware that exposure to high levels of aluminum may result in adverse clinical effects and symptoms such as:
    • Bone, muscle pain and muscle weakness
    • Blood and metabolic derangements (such as increased levels of calcium or interference with iron absorption leading to anemia)
    • Neurological effects (such as altered consciousness, seizures, and coma).
  • Conduct a clinical benefit-risk analysis before using a fluid warmer which has an aluminum heating element and is in direct contact with the fluids or blood products. To mitigate potential harm from aluminum leaching:
    • When possible, avoid using these fluid warmers in high-risk patient populations including those with poor renal function, neonates, infants, pregnant mothers, and the elderly because exposure to small amounts of aluminum may lead to toxicity. 
    • If available, use alternative therapies to maintain patient temperature, such as an alternative fluid warmer which uses a different design, or a warming blanket.
  • For specific information on steps to take to mitigate aluminum leaching, review the applicable recall notices from each company (see table above) or contact the manufacturer directly for more information.


Fluid warmers are generally used to warm intravenous (IV) fluids and blood products to maintain normal temperature or prevent hypothermia and can also be used during surgical procedures for surgical site irrigation or lavage in different areas of the body. These devices have different clinical uses which impact their device design and specifications, including flow rate and heating capabilities, duration of use, and intended patient populations.

Data from in vitro testing with uncoated fluid warmers indicates that in certain cases (for example, lower flow rates, higher temperatures, certain infusates such as balanced electrolyte solutions, and longer duration of use), the quantity of aluminum released from these devices may significantly exceed the FDA-derived threshold value of 25 mcg/L, which was established for small and large volume parenteral administration. The dissolving (elution) of aluminum into the body may lead to systemic aluminum exposure and subsequent toxicity under some clinical situations and with high-risk patient populations including neonates, infants, pregnant mothers, and the elderly as well as patients with poor renal function or on dialysis. Literature reports describe neurotoxicity concomitant with increased aluminum serum levels. For example, manifestations of encephalopathy after irrigation with solutions containing aluminum have been reported at serum concentrations as low as 17, 22, or 40 mcg AL/L blood. See Additional Resources below for details on the literature reports and data.

The FDA is not aware of any reported cases of aluminum toxicity or high levels of aluminum exposure associated with the clinical use of these fluid warmers. Symptoms of harmful levels of aluminum exposure may not be easily recognized and may include bone or muscle pain and weakness, anemia, seizures, or coma. However, it is possible that symptoms associated with high levels of aluminum exposure may be attributed to other comorbidities, disease processes, or side effects from other medications due to lack of awareness of this potential source of aluminum.

FDA Actions

In addition to reminding users who were already provided revised instructions for use by the original equipment manufacturers, we have issued this letter to health care providers to assure that users who may have purchased these models from other sources are aware of these recommendations for reducing or eliminating the risk of aluminum exposure.

The FDA is working with the applicable manufacturers to further mitigate aluminum exposure with this type of device design.

The FDA will continue to keep health care providers and the public informed if significant new information becomes available.

Reporting Problems to the FDA

The FDA encourages health care providers to report any adverse events or suspected adverse events experienced with the fluid warmers.

Prompt reporting of adverse events can help the FDA identify and better understand the risks associated with medical devices.

Additional Resources

Contact Information

If you have questions about this letter, contact the Division of Industry and Consumer Education (DICE).

Back to Top